Filtered by vendor Cisco
Subscriptions
Filtered by product Ios Xe
Subscriptions
Total
538 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-20271 | 1 Cisco | 14 Business 140ac, Business 140ac Access Point, Business 141acm and 11 more | 2025-08-06 | 8.6 High |
| A vulnerability in the IP packet processing of Cisco Access Point (AP) Software could allow an unauthenticated, remote attacker to cause a denial of service (DoS) condition on an affected device. This vulnerability is due to insufficient input validation of certain IPv4 packets. An attacker could exploit this vulnerability by sending a crafted IPv4 packet either to or through an affected device. A successful exploit could allow the attacker to cause an affected device to reload unexpectedly, resulting in a DoS condition. To successfully exploit this vulnerability, the attacker does not need to be associated with the affected AP. This vulnerability cannot be exploited by sending IPv6 packets. | ||||
| CVE-2025-20214 | 1 Cisco | 1 Ios Xe | 2025-08-05 | 4.3 Medium |
| A vulnerability in the Network Configuration Access Control Module (NACM) of Cisco IOS XE Software could allow an authenticated, remote attacker to obtain unauthorized read access to configuration or operational data. This vulnerability exists because a subtle change in inner API call behavior causes results to be filtered incorrectly. An attacker could exploit this vulnerability by using either NETCONF, RESTCONF, or gRPC Network Management Interface (gNMI) protocols and query data on paths that may have been denied by the NACM configuration. A successful exploit could allow the attacker to access data that should have been restricted according to the NACM configuration. Note: This vulnerability requires that the attacker obtain the credentials from a valid user with privileges lower than 15, and that NACM was configured to provide restricted read access for that user. | ||||
| CVE-2025-20189 | 1 Cisco | 2 Asr 903, Ios Xe | 2025-08-05 | 7.4 High |
| A vulnerability in the Cisco Express Forwarding functionality of Cisco IOS XE Software for Cisco ASR 903 Aggregation Services Routers with Route Switch Processor 3 (RSP3C) could allow an unauthenticated, adjacent attacker to trigger a denial of service (DoS) condition. This vulnerability is due to improper memory management when Cisco IOS XE Software is processing Address Resolution Protocol (ARP) messages. An attacker could exploit this vulnerability by sending crafted ARP messages at a high rate over a period of time to an affected device. A successful exploit could allow the attacker to exhaust system resources, which eventually triggers a reload of the active route switch processor (RSP). If a redundant RSP is not present, the router reloads. | ||||
| CVE-2025-20151 | 1 Cisco | 4 Cisco Ios, Ios, Ios Xe and 1 more | 2025-08-05 | 4.3 Medium |
| A vulnerability in the implementation of the Simple Network Management Protocol Version 3 (SNMPv3) feature of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to poll an affected device using SNMP, even if the device is configured to deny SNMP traffic from an unauthorized source or the SNMPv3 username is removed from the configuration. This vulnerability exists because of the way that the SNMPv3 configuration is stored in the Cisco IOS Software and Cisco IOS XE Software startup configuration. An attacker could exploit this vulnerability by polling an affected device from a source address that should have been denied. A successful exploit could allow the attacker to perform SNMP operations from a source that should be denied. Note: The attacker has no control of the SNMPv3 configuration. To exploit this vulnerability, the attacker must have valid SNMPv3 user credentials. For more information, see the section of this advisory. | ||||
| CVE-2025-20201 | 1 Cisco | 2 Ios Xe, Ios Xe Software | 2025-08-01 | 6.7 Medium |
| A vulnerability in the CLI of Cisco IOS XE Software could allow an authenticated, local attacker with privilege level 15 to elevate privileges to root on the underlying operating system of an affected device. This vulnerability is due to insufficient input validation when processing specific configuration commands. An attacker could exploit this vulnerability by including crafted input in specific configuration commands. A successful exploit could allow the attacker to elevate privileges to root on the underlying operating system of an affected device. The security impact rating (SIR) of this advisory has been raised to High because an attacker could gain access to the underlying operating system of the affected device and perform potentially undetected actions. Note: The attacker must have privileges to enter configuration mode on the affected device. This is usually referred to as privilege level 15. | ||||
| CVE-2024-20278 | 1 Cisco | 1 Ios Xe | 2025-08-01 | 6.5 Medium |
| A vulnerability in the NETCONF feature of Cisco IOS XE Software could allow an authenticated, remote attacker to elevate privileges to root on an affected device. This vulnerability is due to improper validation of user-supplied input. An attacker could exploit this vulnerability by sending crafted input over NETCONF to an affected device. A successful exploit could allow the attacker to elevate privileges from Administrator to root. | ||||
| CVE-2022-20920 | 1 Cisco | 2 Ios, Ios Xe | 2025-08-01 | 7.7 High |
| A vulnerability in the SSH implementation of Cisco IOS Software and Cisco IOS XE Software could allow an authenticated, remote attacker to cause an affected device to reload. This vulnerability is due to improper handling of resources during an exceptional situation. An attacker could exploit this vulnerability by continuously connecting to an affected device and sending specific SSH requests. A successful exploit could allow the attacker to cause the affected device to reload. | ||||
| CVE-2017-6743 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6742 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6741 | 1 Cisco | 1 Ios Xe | 2025-07-31 | N/A |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6740 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6739 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6738 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2017-6737 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| A vulnerability in the SNMP implementation of could allow an authenticated, remote attacker to cause a reload of the affected system or to remotely execute code. An attacker could exploit this vulnerability by sending a crafted SNMP packet to the affected device. The vulnerability is due to a buffer overflow in the affected code area. The vulnerability affects all versions of SNMP (versions 1, 2c, and 3). The attacker must know the SNMP read only community string (SNMP version 2c or earlier) or the user credentials (SNMPv3). An exploit could allow the attacker to execute arbitrary code and obtain full control of the system or to cause a reload of the affected system. Only traffic directed to the affected system can be used to exploit this vulnerability. | ||||
| CVE-2017-6736 | 1 Cisco | 2 Ios, Ios Xe | 2025-07-31 | 8.8 High |
| The Simple Network Management Protocol (SNMP) subsystem of Cisco IOS and IOS XE Software contains multiple vulnerabilities that could allow an authenticated, remote attacker to remotely execute code on an affected system or cause an affected system to reload. An attacker could exploit these vulnerabilities by sending a crafted SNMP packet to an affected system via IPv4 or IPv6. Only traffic directed to an affected system can be used to exploit these vulnerabilities. The vulnerabilities are due to a buffer overflow condition in the SNMP subsystem of the affected software. The vulnerabilities affect all versions of SNMP - Versions 1, 2c, and 3. To exploit these vulnerabilities via SNMP Version 2c or earlier, the attacker must know the SNMP read-only community string for the affected system. To exploit these vulnerabilities via SNMP Version 3, the attacker must have user credentials for the affected system. A successful exploit could allow the attacker to execute arbitrary code and obtain full control of the affected system or cause the affected system to reload. Customers are advised to apply the workaround as contained in the Workarounds section below. Fixed software information is available via the Cisco IOS Software Checker. All devices that have enabled SNMP and have not explicitly excluded the affected MIBs or OIDs should be considered vulnerable. There are workarounds that address these vulnerabilities. | ||||
| CVE-2025-20140 | 1 Cisco | 17 Catalyst 9105axi, Catalyst 9115axe, Catalyst 9115axi and 14 more | 2025-07-31 | 7.4 High |
| A vulnerability in the Wireless Network Control daemon (wncd) of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, adjacent wireless attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper memory management. An attacker could exploit this vulnerability by sending a series of IPv6 network requests from an associated wireless IPv6 client to an affected device. To associate a client to a device, an attacker may first need to authenticate to the network, or associate freely in the case of a configured open network. A successful exploit could allow the attacker to cause the wncd process to consume available memory and eventually cause the device to stop responding, resulting in a DoS condition. | ||||
| CVE-2024-20303 | 1 Cisco | 17 Catalyst 9105axi, Catalyst 9115axe, Catalyst 9115axi and 14 more | 2025-07-31 | 7.4 High |
| A vulnerability in the multicast DNS (mDNS) gateway feature of Cisco IOS XE Software for Wireless LAN Controllers (WLCs) could allow an unauthenticated, adjacent attacker to cause a denial of service (DoS) condition. This vulnerability is due to improper management of mDNS client entries. An attacker could exploit this vulnerability by connecting to the wireless network and sending a continuous stream of specific mDNS packets. A successful exploit could allow the attacker to cause the wireless controller to have high CPU utilization, which could lead to access points (APs) losing their connection to the controller and result in a DoS condition. | ||||
| CVE-2025-20154 | 1 Cisco | 3 Ios, Ios Xe, Ios Xr | 2025-07-31 | 8.6 High |
| A vulnerability in the Two-Way Active Measurement Protocol (TWAMP) server feature of Cisco IOS Software and Cisco IOS XE Software could allow an unauthenticated, remote attacker to cause the affected device to reload, resulting in a denial of service (DoS) condition. For Cisco IOS XR Software, this vulnerability could cause the ipsla_ippm_server process to reload unexpectedly if debugs are enabled. This vulnerability is due to out-of-bounds array access when processing specially crafted TWAMP control packets. An attacker could exploit this vulnerability by sending crafted TWAMP control packets to an affected device. A successful exploit could allow the attacker to cause the affected device to reload, resulting in a DoS condition. Note: For Cisco IOS XR Software, only the ipsla_ippm_server process reloads unexpectedly and only when debugs are enabled. The vulnerability details for Cisco IOS XR Software are as follows: Security Impact Rating (SIR): Low CVSS Base Score: 3.7 CVSS Vector: CVSS:3.1/AV:N/AC:H/PR:N/UI:N/S:U/C:N/I:N/A:L | ||||
| CVE-2025-20190 | 1 Cisco | 17 Catalyst 9105axi, Catalyst 9115axe, Catalyst 9115axi and 14 more | 2025-07-31 | 6.5 Medium |
| A vulnerability in the lobby ambassador web interface of Cisco IOS XE Wireless Controller Software could allow an authenticated, remote attacker to remove arbitrary users that are defined on an affected device. This vulnerability is due to insufficient access control of actions executed by lobby ambassador users. An attacker could exploit this vulnerability by logging in to an affected device with a lobby ambassador user account and sending crafted HTTP requests to the API. A successful exploit could allow the attacker to delete arbitrary user accounts on the device, including users with administrative privileges. Note: This vulnerability is exploitable only if the attacker obtains the credentials for a lobby ambassador account. This account is not configured by default. | ||||
| CVE-2025-20155 | 1 Cisco | 1 Ios Xe | 2025-07-31 | 6 Medium |
| A vulnerability in the bootstrap loading of Cisco IOS XE Software could allow an authenticated, local attacker to write arbitrary files to an affected system. This vulnerability is due to insufficient input validation of the bootstrap file that is read by the system software when a device is first deployed in SD-WAN mode or when an administrator configures SD-Routing on the device. An attacker could exploit this vulnerability by modifying a bootstrap file generated by Cisco Catalyst SD-WAN Manager, loading it into the device flash, and then either reloading the device in a green field deployment in SD-WAN mode or configuring the device with SD-Routing. A successful exploit could allow the attacker to perform arbitrary file writes to the underlying operating system. | ||||