Total
8223 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-58007 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: soc: qcom: socinfo: Avoid out of bounds read of serial number On MSM8916 devices, the serial number exposed in sysfs is constant and does not change across individual devices. It's always: db410c:/sys/devices/soc0$ cat serial_number 2644893864 The firmware used on MSM8916 exposes SOCINFO_VERSION(0, 8), which does not have support for the serial_num field in the socinfo struct. There is an existing check to avoid exposing the serial number in that case, but it's not correct: When checking the item_size returned by SMEM, we need to make sure the *end* of the serial_num is within bounds, instead of comparing with the *start* offset. The serial_number currently exposed on MSM8916 devices is just an out of bounds read of whatever comes after the socinfo struct in SMEM. Fix this by changing offsetof() to offsetofend(), so that the size of the field is also taken into account. | ||||
| CVE-2024-57982 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: xfrm: state: fix out-of-bounds read during lookup lookup and resize can run in parallel. The xfrm_state_hash_generation seqlock ensures a retry, but the hash functions can observe a hmask value that is too large for the new hlist array. rehash does: rcu_assign_pointer(net->xfrm.state_bydst, ndst) [..] net->xfrm.state_hmask = nhashmask; While state lookup does: h = xfrm_dst_hash(net, daddr, saddr, tmpl->reqid, encap_family); hlist_for_each_entry_rcu(x, net->xfrm.state_bydst + h, bydst) { This is only safe in case the update to state_bydst is larger than net->xfrm.xfrm_state_hmask (or if the lookup function gets serialized via state spinlock again). Fix this by prefetching state_hmask and the associated pointers. The xfrm_state_hash_generation seqlock retry will ensure that the pointer and the hmask will be consistent. The existing helpers, like xfrm_dst_hash(), are now unsafe for RCU side, add lockdep assertions to document that they are only safe for insert side. xfrm_state_lookup_byaddr() uses the spinlock rather than RCU. AFAICS this is an oversight from back when state lookup was converted to RCU, this lock should be replaced with RCU in a future patch. | ||||
| CVE-2024-56721 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: x86/CPU/AMD: Terminate the erratum_1386_microcode array The erratum_1386_microcode array requires an empty entry at the end. Otherwise x86_match_cpu_with_stepping() will continue iterate the array after it ended. Add an empty entry to erratum_1386_microcode to its end. | ||||
| CVE-2024-56650 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: x_tables: fix LED ID check in led_tg_check() Syzbot has reported the following BUG detected by KASAN: BUG: KASAN: slab-out-of-bounds in strlen+0x58/0x70 Read of size 1 at addr ffff8881022da0c8 by task repro/5879 ... Call Trace: <TASK> dump_stack_lvl+0x241/0x360 ? __pfx_dump_stack_lvl+0x10/0x10 ? __pfx__printk+0x10/0x10 ? _printk+0xd5/0x120 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 print_report+0x169/0x550 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x183/0x530 ? __virt_addr_valid+0x45f/0x530 ? __phys_addr+0xba/0x170 ? strlen+0x58/0x70 kasan_report+0x143/0x180 ? strlen+0x58/0x70 strlen+0x58/0x70 kstrdup+0x20/0x80 led_tg_check+0x18b/0x3c0 xt_check_target+0x3bb/0xa40 ? __pfx_xt_check_target+0x10/0x10 ? stack_depot_save_flags+0x6e4/0x830 ? nft_target_init+0x174/0xc30 nft_target_init+0x82d/0xc30 ? __pfx_nft_target_init+0x10/0x10 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? rcu_is_watching+0x15/0xb0 ? nf_tables_newrule+0x1609/0x2980 ? nf_tables_newrule+0x1609/0x2980 ? __kmalloc_noprof+0x21a/0x400 nf_tables_newrule+0x1860/0x2980 ? __pfx_nf_tables_newrule+0x10/0x10 ? __nla_parse+0x40/0x60 nfnetlink_rcv+0x14e5/0x2ab0 ? __pfx_validate_chain+0x10/0x10 ? __pfx_nfnetlink_rcv+0x10/0x10 ? __lock_acquire+0x1384/0x2050 ? netlink_deliver_tap+0x2e/0x1b0 ? __pfx_lock_release+0x10/0x10 ? netlink_deliver_tap+0x2e/0x1b0 netlink_unicast+0x7f8/0x990 ? __pfx_netlink_unicast+0x10/0x10 ? __virt_addr_valid+0x183/0x530 ? __check_object_size+0x48e/0x900 netlink_sendmsg+0x8e4/0xcb0 ? __pfx_netlink_sendmsg+0x10/0x10 ? aa_sock_msg_perm+0x91/0x160 ? __pfx_netlink_sendmsg+0x10/0x10 __sock_sendmsg+0x223/0x270 ____sys_sendmsg+0x52a/0x7e0 ? __pfx_____sys_sendmsg+0x10/0x10 __sys_sendmsg+0x292/0x380 ? __pfx___sys_sendmsg+0x10/0x10 ? lockdep_hardirqs_on_prepare+0x43d/0x780 ? __pfx_lockdep_hardirqs_on_prepare+0x10/0x10 ? exc_page_fault+0x590/0x8c0 ? do_syscall_64+0xb6/0x230 do_syscall_64+0xf3/0x230 entry_SYSCALL_64_after_hwframe+0x77/0x7f ... </TASK> Since an invalid (without '\0' byte at all) byte sequence may be passed from userspace, add an extra check to ensure that such a sequence is rejected as possible ID and so never passed to 'kstrdup()' and further. | ||||
| CVE-2024-56627 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: ksmbd: fix Out-of-Bounds Read in ksmbd_vfs_stream_read An offset from client could be a negative value, It could lead to an out-of-bounds read from the stream_buf. Note that this issue is coming when setting 'vfs objects = streams_xattr parameter' in ksmbd.conf. | ||||
| CVE-2024-56555 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: binder: fix OOB in binder_add_freeze_work() In binder_add_freeze_work() we iterate over the proc->nodes with the proc->inner_lock held. However, this lock is temporarily dropped to acquire the node->lock first (lock nesting order). This can race with binder_deferred_release() which removes the nodes from the proc->nodes rbtree and adds them into binder_dead_nodes list. This leads to a broken iteration in binder_add_freeze_work() as rb_next() will use data from binder_dead_nodes, triggering an out-of-bounds access: ================================================================== BUG: KASAN: global-out-of-bounds in rb_next+0xfc/0x124 Read of size 8 at addr ffffcb84285f7170 by task freeze/660 CPU: 8 UID: 0 PID: 660 Comm: freeze Not tainted 6.11.0-07343-ga727812a8d45 #18 Hardware name: linux,dummy-virt (DT) Call trace: rb_next+0xfc/0x124 binder_add_freeze_work+0x344/0x534 binder_ioctl+0x1e70/0x25ac __arm64_sys_ioctl+0x124/0x190 The buggy address belongs to the variable: binder_dead_nodes+0x10/0x40 [...] ================================================================== This is possible because proc->nodes (rbtree) and binder_dead_nodes (list) share entries in binder_node through a union: struct binder_node { [...] union { struct rb_node rb_node; struct hlist_node dead_node; }; Fix the race by checking that the proc is still alive. If not, simply break out of the iteration. | ||||
| CVE-2024-53163 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: crypto: qat/qat_420xx - fix off by one in uof_get_name() This is called from uof_get_name_420xx() where "num_objs" is the ARRAY_SIZE() of fw_objs[]. The > needs to be >= to prevent an out of bounds access. | ||||
| CVE-2024-53162 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: crypto: qat/qat_4xxx - fix off by one in uof_get_name() The fw_objs[] array has "num_objs" elements so the > needs to be >= to prevent an out of bounds read. | ||||
| CVE-2024-53082 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: virtio_net: Add hash_key_length check Add hash_key_length check in virtnet_probe() to avoid possible out of bound errors when setting/reading the hash key. | ||||
| CVE-2024-53065 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mm/slab: fix warning caused by duplicate kmem_cache creation in kmem_buckets_create Commit b035f5a6d852 ("mm: slab: reduce the kmalloc() minimum alignment if DMA bouncing possible") reduced ARCH_KMALLOC_MINALIGN to 8 on arm64. However, with KASAN_HW_TAGS enabled, arch_slab_minalign() becomes 16. This causes kmalloc_caches[*][8] to be aliased to kmalloc_caches[*][16], resulting in kmem_buckets_create() attempting to create a kmem_cache for size 16 twice. This duplication triggers warnings on boot: [ 2.325108] ------------[ cut here ]------------ [ 2.325135] kmem_cache of name 'memdup_user-16' already exists [ 2.325783] WARNING: CPU: 0 PID: 1 at mm/slab_common.c:107 __kmem_cache_create_args+0xb8/0x3b0 [ 2.327957] Modules linked in: [ 2.328550] CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.12.0-rc5mm-unstable-arm64+ #12 [ 2.328683] Hardware name: QEMU QEMU Virtual Machine, BIOS 2024.02-2 03/11/2024 [ 2.328790] pstate: 61000009 (nZCv daif -PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 2.328911] pc : __kmem_cache_create_args+0xb8/0x3b0 [ 2.328930] lr : __kmem_cache_create_args+0xb8/0x3b0 [ 2.328942] sp : ffff800083d6fc50 [ 2.328961] x29: ffff800083d6fc50 x28: f2ff0000c1674410 x27: ffff8000820b0598 [ 2.329061] x26: 000000007fffffff x25: 0000000000000010 x24: 0000000000002000 [ 2.329101] x23: ffff800083d6fce8 x22: ffff8000832222e8 x21: ffff800083222388 [ 2.329118] x20: f2ff0000c1674410 x19: f5ff0000c16364c0 x18: ffff800083d80030 [ 2.329135] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 2.329152] x14: 0000000000000000 x13: 0a73747369786520 x12: 79646165726c6120 [ 2.329169] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : 0000000000000000 [ 2.329194] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 [ 2.329210] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 [ 2.329226] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 [ 2.329291] Call trace: [ 2.329407] __kmem_cache_create_args+0xb8/0x3b0 [ 2.329499] kmem_buckets_create+0xfc/0x320 [ 2.329526] init_user_buckets+0x34/0x78 [ 2.329540] do_one_initcall+0x64/0x3c8 [ 2.329550] kernel_init_freeable+0x26c/0x578 [ 2.329562] kernel_init+0x3c/0x258 [ 2.329574] ret_from_fork+0x10/0x20 [ 2.329698] ---[ end trace 0000000000000000 ]--- [ 2.403704] ------------[ cut here ]------------ [ 2.404716] kmem_cache of name 'msg_msg-16' already exists [ 2.404801] WARNING: CPU: 2 PID: 1 at mm/slab_common.c:107 __kmem_cache_create_args+0xb8/0x3b0 [ 2.404842] Modules linked in: [ 2.404971] CPU: 2 UID: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.12.0-rc5mm-unstable-arm64+ #12 [ 2.405026] Tainted: [W]=WARN [ 2.405043] Hardware name: QEMU QEMU Virtual Machine, BIOS 2024.02-2 03/11/2024 [ 2.405057] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 2.405079] pc : __kmem_cache_create_args+0xb8/0x3b0 [ 2.405100] lr : __kmem_cache_create_args+0xb8/0x3b0 [ 2.405111] sp : ffff800083d6fc50 [ 2.405115] x29: ffff800083d6fc50 x28: fbff0000c1674410 x27: ffff8000820b0598 [ 2.405135] x26: 000000000000ffd0 x25: 0000000000000010 x24: 0000000000006000 [ 2.405153] x23: ffff800083d6fce8 x22: ffff8000832222e8 x21: ffff800083222388 [ 2.405169] x20: fbff0000c1674410 x19: fdff0000c163d6c0 x18: ffff800083d80030 [ 2.405185] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000 [ 2.405201] x14: 0000000000000000 x13: 0a73747369786520 x12: 79646165726c6120 [ 2.405217] x11: 656820747563205b x10: 2d2d2d2d2d2d2d2d x9 : 0000000000000000 [ 2.405233] x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 [ 2.405248] x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000 [ 2.405271] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000 [ 2.405287] Call trace: [ 2 ---truncated--- | ||||
| CVE-2024-53058 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net: stmmac: TSO: Fix unbalanced DMA map/unmap for non-paged SKB data In case the non-paged data of a SKB carries protocol header and protocol payload to be transmitted on a certain platform that the DMA AXI address width is configured to 40-bit/48-bit, or the size of the non-paged data is bigger than TSO_MAX_BUFF_SIZE on a certain platform that the DMA AXI address width is configured to 32-bit, then this SKB requires at least two DMA transmit descriptors to serve it. For example, three descriptors are allocated to split one DMA buffer mapped from one piece of non-paged data: dma_desc[N + 0], dma_desc[N + 1], dma_desc[N + 2]. Then three elements of tx_q->tx_skbuff_dma[] will be allocated to hold extra information to be reused in stmmac_tx_clean(): tx_q->tx_skbuff_dma[N + 0], tx_q->tx_skbuff_dma[N + 1], tx_q->tx_skbuff_dma[N + 2]. Now we focus on tx_q->tx_skbuff_dma[entry].buf, which is the DMA buffer address returned by DMA mapping call. stmmac_tx_clean() will try to unmap the DMA buffer _ONLY_IF_ tx_q->tx_skbuff_dma[entry].buf is a valid buffer address. The expected behavior that saves DMA buffer address of this non-paged data to tx_q->tx_skbuff_dma[entry].buf is: tx_q->tx_skbuff_dma[N + 0].buf = NULL; tx_q->tx_skbuff_dma[N + 1].buf = NULL; tx_q->tx_skbuff_dma[N + 2].buf = dma_map_single(); Unfortunately, the current code misbehaves like this: tx_q->tx_skbuff_dma[N + 0].buf = dma_map_single(); tx_q->tx_skbuff_dma[N + 1].buf = NULL; tx_q->tx_skbuff_dma[N + 2].buf = NULL; On the stmmac_tx_clean() side, when dma_desc[N + 0] is closed by the DMA engine, tx_q->tx_skbuff_dma[N + 0].buf is a valid buffer address obviously, then the DMA buffer will be unmapped immediately. There may be a rare case that the DMA engine does not finish the pending dma_desc[N + 1], dma_desc[N + 2] yet. Now things will go horribly wrong, DMA is going to access a unmapped/unreferenced memory region, corrupted data will be transmited or iommu fault will be triggered :( In contrast, the for-loop that maps SKB fragments behaves perfectly as expected, and that is how the driver should do for both non-paged data and paged frags actually. This patch corrects DMA map/unmap sequences by fixing the array index for tx_q->tx_skbuff_dma[entry].buf when assigning DMA buffer address. Tested and verified on DWXGMAC CORE 3.20a | ||||
| CVE-2024-50301 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: security/keys: fix slab-out-of-bounds in key_task_permission KASAN reports an out of bounds read: BUG: KASAN: slab-out-of-bounds in __kuid_val include/linux/uidgid.h:36 BUG: KASAN: slab-out-of-bounds in uid_eq include/linux/uidgid.h:63 [inline] BUG: KASAN: slab-out-of-bounds in key_task_permission+0x394/0x410 security/keys/permission.c:54 Read of size 4 at addr ffff88813c3ab618 by task stress-ng/4362 CPU: 2 PID: 4362 Comm: stress-ng Not tainted 5.10.0-14930-gafbffd6c3ede #15 Call Trace: __dump_stack lib/dump_stack.c:82 [inline] dump_stack+0x107/0x167 lib/dump_stack.c:123 print_address_description.constprop.0+0x19/0x170 mm/kasan/report.c:400 __kasan_report.cold+0x6c/0x84 mm/kasan/report.c:560 kasan_report+0x3a/0x50 mm/kasan/report.c:585 __kuid_val include/linux/uidgid.h:36 [inline] uid_eq include/linux/uidgid.h:63 [inline] key_task_permission+0x394/0x410 security/keys/permission.c:54 search_nested_keyrings+0x90e/0xe90 security/keys/keyring.c:793 This issue was also reported by syzbot. It can be reproduced by following these steps(more details [1]): 1. Obtain more than 32 inputs that have similar hashes, which ends with the pattern '0xxxxxxxe6'. 2. Reboot and add the keys obtained in step 1. The reproducer demonstrates how this issue happened: 1. In the search_nested_keyrings function, when it iterates through the slots in a node(below tag ascend_to_node), if the slot pointer is meta and node->back_pointer != NULL(it means a root), it will proceed to descend_to_node. However, there is an exception. If node is the root, and one of the slots points to a shortcut, it will be treated as a keyring. 2. Whether the ptr is keyring decided by keyring_ptr_is_keyring function. However, KEYRING_PTR_SUBTYPE is 0x2UL, the same as ASSOC_ARRAY_PTR_SUBTYPE_MASK. 3. When 32 keys with the similar hashes are added to the tree, the ROOT has keys with hashes that are not similar (e.g. slot 0) and it splits NODE A without using a shortcut. When NODE A is filled with keys that all hashes are xxe6, the keys are similar, NODE A will split with a shortcut. Finally, it forms the tree as shown below, where slot 6 points to a shortcut. NODE A +------>+---+ ROOT | | 0 | xxe6 +---+ | +---+ xxxx | 0 | shortcut : : xxe6 +---+ | +---+ xxe6 : : | | | xxe6 +---+ | +---+ | 6 |---+ : : xxe6 +---+ +---+ xxe6 : : | f | xxe6 +---+ +---+ xxe6 | f | +---+ 4. As mentioned above, If a slot(slot 6) of the root points to a shortcut, it may be mistakenly transferred to a key*, leading to a read out-of-bounds read. To fix this issue, one should jump to descend_to_node if the ptr is a shortcut, regardless of whether the node is root or not. [1] https://lore.kernel.org/linux-kernel/1cfa878e-8c7b-4570-8606-21daf5e13ce7@huaweicloud.com/ [jarkko: tweaked the commit message a bit to have an appropriate closes tag.] | ||||
| CVE-2024-50279 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: dm cache: fix out-of-bounds access to the dirty bitset when resizing dm-cache checks the dirty bits of the cache blocks to be dropped when shrinking the fast device, but an index bug in bitset iteration causes out-of-bounds access. Reproduce steps: 1. create a cache device of 1024 cache blocks (128 bytes dirty bitset) dmsetup create cmeta --table "0 8192 linear /dev/sdc 0" dmsetup create cdata --table "0 131072 linear /dev/sdc 8192" dmsetup create corig --table "0 524288 linear /dev/sdc 262144" dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct dmsetup create cache --table "0 524288 cache /dev/mapper/cmeta \ /dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0" 2. shrink the fast device to 512 cache blocks, triggering out-of-bounds access to the dirty bitset (offset 0x80) dmsetup suspend cache dmsetup reload cdata --table "0 65536 linear /dev/sdc 8192" dmsetup resume cdata dmsetup resume cache KASAN reports: BUG: KASAN: vmalloc-out-of-bounds in cache_preresume+0x269/0x7b0 Read of size 8 at addr ffffc900000f3080 by task dmsetup/131 (...snip...) The buggy address belongs to the virtual mapping at [ffffc900000f3000, ffffc900000f5000) created by: cache_ctr+0x176a/0x35f0 (...snip...) Memory state around the buggy address: ffffc900000f2f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc900000f3000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 >ffffc900000f3080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ^ ffffc900000f3100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc900000f3180: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 Fix by making the index post-incremented. | ||||
| CVE-2024-50278 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: dm cache: fix potential out-of-bounds access on the first resume Out-of-bounds access occurs if the fast device is expanded unexpectedly before the first-time resume of the cache table. This happens because expanding the fast device requires reloading the cache table for cache_create to allocate new in-core data structures that fit the new size, and the check in cache_preresume is not performed during the first resume, leading to the issue. Reproduce steps: 1. prepare component devices: dmsetup create cmeta --table "0 8192 linear /dev/sdc 0" dmsetup create cdata --table "0 65536 linear /dev/sdc 8192" dmsetup create corig --table "0 524288 linear /dev/sdc 262144" dd if=/dev/zero of=/dev/mapper/cmeta bs=4k count=1 oflag=direct 2. load a cache table of 512 cache blocks, and deliberately expand the fast device before resuming the cache, making the in-core data structures inadequate. dmsetup create cache --notable dmsetup reload cache --table "0 524288 cache /dev/mapper/cmeta \ /dev/mapper/cdata /dev/mapper/corig 128 2 metadata2 writethrough smq 0" dmsetup reload cdata --table "0 131072 linear /dev/sdc 8192" dmsetup resume cdata dmsetup resume cache 3. suspend the cache to write out the in-core dirty bitset and hint array, leading to out-of-bounds access to the dirty bitset at offset 0x40: dmsetup suspend cache KASAN reports: BUG: KASAN: vmalloc-out-of-bounds in is_dirty_callback+0x2b/0x80 Read of size 8 at addr ffffc90000085040 by task dmsetup/90 (...snip...) The buggy address belongs to the virtual mapping at [ffffc90000085000, ffffc90000087000) created by: cache_ctr+0x176a/0x35f0 (...snip...) Memory state around the buggy address: ffffc90000084f00: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc90000084f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 >ffffc90000085000: 00 00 00 00 00 00 00 00 f8 f8 f8 f8 f8 f8 f8 f8 ^ ffffc90000085080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 ffffc90000085100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 Fix by checking the size change on the first resume. | ||||
| CVE-2024-50268 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: usb: typec: fix potential out of bounds in ucsi_ccg_update_set_new_cam_cmd() The "*cmd" variable can be controlled by the user via debugfs. That means "new_cam" can be as high as 255 while the size of the uc->updated[] array is UCSI_MAX_ALTMODES (30). The call tree is: ucsi_cmd() // val comes from simple_attr_write_xsigned() -> ucsi_send_command() -> ucsi_send_command_common() -> ucsi_run_command() // calls ucsi->ops->sync_control() -> ucsi_ccg_sync_control() | ||||
| CVE-2024-50259 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netdevsim: Add trailing zero to terminate the string in nsim_nexthop_bucket_activity_write() This was found by a static analyzer. We should not forget the trailing zero after copy_from_user() if we will further do some string operations, sscanf() in this case. Adding a trailing zero will ensure that the function performs properly. | ||||
| CVE-2024-50248 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ntfs3: Add bounds checking to mi_enum_attr() Added bounds checking to make sure that every attr don't stray beyond valid memory region. | ||||
| CVE-2024-50247 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: fs/ntfs3: Check if more than chunk-size bytes are written A incorrectly formatted chunk may decompress into more than LZNT_CHUNK_SIZE bytes and a index out of bounds will occur in s_max_off. | ||||
| CVE-2024-50227 | 1 Linux | 1 Linux Kernel | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: thunderbolt: Fix KASAN reported stack out-of-bounds read in tb_retimer_scan() KASAN reported following issue: BUG: KASAN: stack-out-of-bounds in tb_retimer_scan+0xffe/0x1550 [thunderbolt] Read of size 4 at addr ffff88810111fc1c by task kworker/u56:0/11 CPU: 0 UID: 0 PID: 11 Comm: kworker/u56:0 Tainted: G U 6.11.0+ #1387 Tainted: [U]=USER Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt] Call Trace: <TASK> dump_stack_lvl+0x6c/0x90 print_report+0xd1/0x630 kasan_report+0xdb/0x110 __asan_report_load4_noabort+0x14/0x20 tb_retimer_scan+0xffe/0x1550 [thunderbolt] tb_scan_port+0xa6f/0x2060 [thunderbolt] tb_handle_hotplug+0x17b1/0x3080 [thunderbolt] process_one_work+0x626/0x1100 worker_thread+0x6c8/0xfa0 kthread+0x2c8/0x3a0 ret_from_fork+0x3a/0x80 ret_from_fork_asm+0x1a/0x30 This happens because the loop variable still gets incremented by one so max becomes 3 instead of 2, and this makes the second loop read past the the array declared on the stack. Fix this by assigning to max directly in the loop body. | ||||
| CVE-2024-50208 | 2 Linux, Redhat | 2 Linux Kernel, Enterprise Linux | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/bnxt_re: Fix a bug while setting up Level-2 PBL pages Avoid memory corruption while setting up Level-2 PBL pages for the non MR resources when num_pages > 256K. There will be a single PDE page address (contiguous pages in the case of > PAGE_SIZE), but, current logic assumes multiple pages, leading to invalid memory access after 256K PBL entries in the PDE. | ||||