Filtered by vendor Redhat
Subscriptions
Filtered by product Rhel Eus
Subscriptions
Total
2948 CVE
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2024-26759 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: mm/swap: fix race when skipping swapcache When skipping swapcache for SWP_SYNCHRONOUS_IO, if two or more threads swapin the same entry at the same time, they get different pages (A, B). Before one thread (T0) finishes the swapin and installs page (A) to the PTE, another thread (T1) could finish swapin of page (B), swap_free the entry, then swap out the possibly modified page reusing the same entry. It breaks the pte_same check in (T0) because PTE value is unchanged, causing ABA problem. Thread (T0) will install a stalled page (A) into the PTE and cause data corruption. One possible callstack is like this: CPU0 CPU1 ---- ---- do_swap_page() do_swap_page() with same entry <direct swapin path> <direct swapin path> <alloc page A> <alloc page B> swap_read_folio() <- read to page A swap_read_folio() <- read to page B <slow on later locks or interrupt> <finished swapin first> ... set_pte_at() swap_free() <- entry is free <write to page B, now page A stalled> <swap out page B to same swap entry> pte_same() <- Check pass, PTE seems unchanged, but page A is stalled! swap_free() <- page B content lost! set_pte_at() <- staled page A installed! And besides, for ZRAM, swap_free() allows the swap device to discard the entry content, so even if page (B) is not modified, if swap_read_folio() on CPU0 happens later than swap_free() on CPU1, it may also cause data loss. To fix this, reuse swapcache_prepare which will pin the swap entry using the cache flag, and allow only one thread to swap it in, also prevent any parallel code from putting the entry in the cache. Release the pin after PT unlocked. Racers just loop and wait since it's a rare and very short event. A schedule_timeout_uninterruptible(1) call is added to avoid repeated page faults wasting too much CPU, causing livelock or adding too much noise to perf statistics. A similar livelock issue was described in commit 029c4628b2eb ("mm: swap: get rid of livelock in swapin readahead") Reproducer: This race issue can be triggered easily using a well constructed reproducer and patched brd (with a delay in read path) [1]: With latest 6.8 mainline, race caused data loss can be observed easily: $ gcc -g -lpthread test-thread-swap-race.c && ./a.out Polulating 32MB of memory region... Keep swapping out... Starting round 0... Spawning 65536 workers... 32746 workers spawned, wait for done... Round 0: Error on 0x5aa00, expected 32746, got 32743, 3 data loss! Round 0: Error on 0x395200, expected 32746, got 32743, 3 data loss! Round 0: Error on 0x3fd000, expected 32746, got 32737, 9 data loss! Round 0 Failed, 15 data loss! This reproducer spawns multiple threads sharing the same memory region using a small swap device. Every two threads updates mapped pages one by one in opposite direction trying to create a race, with one dedicated thread keep swapping out the data out using madvise. The reproducer created a reproduce rate of about once every 5 minutes, so the race should be totally possible in production. After this patch, I ran the reproducer for over a few hundred rounds and no data loss observed. Performance overhead is minimal, microbenchmark swapin 10G from 32G zram: Before: 10934698 us After: 11157121 us Cached: 13155355 us (Dropping SWP_SYNCHRONOUS_IO flag) [kasong@tencent.com: v4] | ||||
| CVE-2024-26744 | 3 Debian, Linux, Redhat | 4 Debian Linux, Linux Kernel, Enterprise Linux and 1 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/srpt: Support specifying the srpt_service_guid parameter Make loading ib_srpt with this parameter set work. The current behavior is that setting that parameter while loading the ib_srpt kernel module triggers the following kernel crash: BUG: kernel NULL pointer dereference, address: 0000000000000000 Call Trace: <TASK> parse_one+0x18c/0x1d0 parse_args+0xe1/0x230 load_module+0x8de/0xa60 init_module_from_file+0x8b/0xd0 idempotent_init_module+0x181/0x240 __x64_sys_finit_module+0x5a/0xb0 do_syscall_64+0x5f/0xe0 entry_SYSCALL_64_after_hwframe+0x6e/0x76 | ||||
| CVE-2024-26743 | 3 Debian, Linux, Redhat | 4 Debian Linux, Linux Kernel, Enterprise Linux and 1 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: RDMA/qedr: Fix qedr_create_user_qp error flow Avoid the following warning by making sure to free the allocated resources in case that qedr_init_user_queue() fail. -----------[ cut here ]----------- WARNING: CPU: 0 PID: 143192 at drivers/infiniband/core/rdma_core.c:874 uverbs_destroy_ufile_hw+0xcf/0xf0 [ib_uverbs] Modules linked in: tls target_core_user uio target_core_pscsi target_core_file target_core_iblock ib_srpt ib_srp scsi_transport_srp nfsd nfs_acl rpcsec_gss_krb5 auth_rpcgss nfsv4 dns_resolver nfs lockd grace fscache netfs 8021q garp mrp stp llc ext4 mbcache jbd2 opa_vnic ib_umad ib_ipoib sunrpc rdma_ucm ib_isert iscsi_target_mod target_core_mod ib_iser libiscsi scsi_transport_iscsi rdma_cm iw_cm ib_cm hfi1 intel_rapl_msr intel_rapl_common mgag200 qedr sb_edac drm_shmem_helper rdmavt x86_pkg_temp_thermal drm_kms_helper intel_powerclamp ib_uverbs coretemp i2c_algo_bit kvm_intel dell_wmi_descriptor ipmi_ssif sparse_keymap kvm ib_core rfkill syscopyarea sysfillrect video sysimgblt irqbypass ipmi_si ipmi_devintf fb_sys_fops rapl iTCO_wdt mxm_wmi iTCO_vendor_support intel_cstate pcspkr dcdbas intel_uncore ipmi_msghandler lpc_ich acpi_power_meter mei_me mei fuse drm xfs libcrc32c qede sd_mod ahci libahci t10_pi sg crct10dif_pclmul crc32_pclmul crc32c_intel qed libata tg3 ghash_clmulni_intel megaraid_sas crc8 wmi [last unloaded: ib_srpt] CPU: 0 PID: 143192 Comm: fi_rdm_tagged_p Kdump: loaded Not tainted 5.14.0-408.el9.x86_64 #1 Hardware name: Dell Inc. PowerEdge R430/03XKDV, BIOS 2.14.0 01/25/2022 RIP: 0010:uverbs_destroy_ufile_hw+0xcf/0xf0 [ib_uverbs] Code: 5d 41 5c 41 5d 41 5e e9 0f 26 1b dd 48 89 df e8 67 6a ff ff 49 8b 86 10 01 00 00 48 85 c0 74 9c 4c 89 e7 e8 83 c0 cb dd eb 92 <0f> 0b eb be 0f 0b be 04 00 00 00 48 89 df e8 8e f5 ff ff e9 6d ff RSP: 0018:ffffb7c6cadfbc60 EFLAGS: 00010286 RAX: ffff8f0889ee3f60 RBX: ffff8f088c1a5200 RCX: 00000000802a0016 RDX: 00000000802a0017 RSI: 0000000000000001 RDI: ffff8f0880042600 RBP: 0000000000000001 R08: 0000000000000001 R09: 0000000000000000 R10: ffff8f11fffd5000 R11: 0000000000039000 R12: ffff8f0d5b36cd80 R13: ffff8f088c1a5250 R14: ffff8f1206d91000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffff8f11d7c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000147069200e20 CR3: 00000001c7210002 CR4: 00000000001706f0 Call Trace: <TASK> ? show_trace_log_lvl+0x1c4/0x2df ? show_trace_log_lvl+0x1c4/0x2df ? ib_uverbs_close+0x1f/0xb0 [ib_uverbs] ? uverbs_destroy_ufile_hw+0xcf/0xf0 [ib_uverbs] ? __warn+0x81/0x110 ? uverbs_destroy_ufile_hw+0xcf/0xf0 [ib_uverbs] ? report_bug+0x10a/0x140 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x14/0x70 ? asm_exc_invalid_op+0x16/0x20 ? uverbs_destroy_ufile_hw+0xcf/0xf0 [ib_uverbs] ib_uverbs_close+0x1f/0xb0 [ib_uverbs] __fput+0x94/0x250 task_work_run+0x5c/0x90 do_exit+0x270/0x4a0 do_group_exit+0x2d/0x90 get_signal+0x87c/0x8c0 arch_do_signal_or_restart+0x25/0x100 ? ib_uverbs_ioctl+0xc2/0x110 [ib_uverbs] exit_to_user_mode_loop+0x9c/0x130 exit_to_user_mode_prepare+0xb6/0x100 syscall_exit_to_user_mode+0x12/0x40 do_syscall_64+0x69/0x90 ? syscall_exit_work+0x103/0x130 ? syscall_exit_to_user_mode+0x22/0x40 ? do_syscall_64+0x69/0x90 ? syscall_exit_work+0x103/0x130 ? syscall_exit_to_user_mode+0x22/0x40 ? do_syscall_64+0x69/0x90 ? do_syscall_64+0x69/0x90 ? common_interrupt+0x43/0xa0 entry_SYSCALL_64_after_hwframe+0x72/0xdc RIP: 0033:0x1470abe3ec6b Code: Unable to access opcode bytes at RIP 0x1470abe3ec41. RSP: 002b:00007fff13ce9108 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: fffffffffffffffc RBX: 00007fff13ce9218 RCX: 00001470abe3ec6b RDX: 00007fff13ce9200 RSI: 00000000c0181b01 RDI: 0000000000000004 RBP: 00007fff13ce91e0 R08: 0000558d9655da10 R09: 0000558d9655dd00 R10: 00007fff13ce95c0 R11: 0000000000000246 R12: 00007fff13ce9358 R13: 0000000000000013 R14: 0000558d9655db50 R15: 00007fff13ce9470 </TASK> --[ end trace 888a9b92e04c5c97 ]-- | ||||
| CVE-2024-26740 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: net/sched: act_mirred: use the backlog for mirred ingress The test Davide added in commit ca22da2fbd69 ("act_mirred: use the backlog for nested calls to mirred ingress") hangs our testing VMs every 10 or so runs, with the familiar tcp_v4_rcv -> tcp_v4_rcv deadlock reported by lockdep. The problem as previously described by Davide (see Link) is that if we reverse flow of traffic with the redirect (egress -> ingress) we may reach the same socket which generated the packet. And we may still be holding its socket lock. The common solution to such deadlocks is to put the packet in the Rx backlog, rather than run the Rx path inline. Do that for all egress -> ingress reversals, not just once we started to nest mirred calls. In the past there was a concern that the backlog indirection will lead to loss of error reporting / less accurate stats. But the current workaround does not seem to address the issue. | ||||
| CVE-2024-26737 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: bpf: Fix racing between bpf_timer_cancel_and_free and bpf_timer_cancel The following race is possible between bpf_timer_cancel_and_free and bpf_timer_cancel. It will lead a UAF on the timer->timer. bpf_timer_cancel(); spin_lock(); t = timer->time; spin_unlock(); bpf_timer_cancel_and_free(); spin_lock(); t = timer->timer; timer->timer = NULL; spin_unlock(); hrtimer_cancel(&t->timer); kfree(t); /* UAF on t */ hrtimer_cancel(&t->timer); In bpf_timer_cancel_and_free, this patch frees the timer->timer after a rcu grace period. This requires a rcu_head addition to the "struct bpf_hrtimer". Another kfree(t) happens in bpf_timer_init, this does not need a kfree_rcu because it is still under the spin_lock and timer->timer has not been visible by others yet. In bpf_timer_cancel, rcu_read_lock() is added because this helper can be used in a non rcu critical section context (e.g. from a sleepable bpf prog). Other timer->timer usages in helpers.c have been audited, bpf_timer_cancel() is the only place where timer->timer is used outside of the spin_lock. Another solution considered is to mark a t->flag in bpf_timer_cancel and clear it after hrtimer_cancel() is done. In bpf_timer_cancel_and_free, it busy waits for the flag to be cleared before kfree(t). This patch goes with a straight forward solution and frees timer->timer after a rcu grace period. | ||||
| CVE-2024-26735 | 4 Debian, Linux, Netapp and 1 more | 22 Debian Linux, Linux Kernel, 8300 and 19 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: ipv6: sr: fix possible use-after-free and null-ptr-deref The pernet operations structure for the subsystem must be registered before registering the generic netlink family. | ||||
| CVE-2024-26733 | 4 Debian, Linux, Netapp and 1 more | 60 Debian Linux, Linux Kernel, 8200 and 57 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: arp: Prevent overflow in arp_req_get(). syzkaller reported an overflown write in arp_req_get(). [0] When ioctl(SIOCGARP) is issued, arp_req_get() looks up an neighbour entry and copies neigh->ha to struct arpreq.arp_ha.sa_data. The arp_ha here is struct sockaddr, not struct sockaddr_storage, so the sa_data buffer is just 14 bytes. In the splat below, 2 bytes are overflown to the next int field, arp_flags. We initialise the field just after the memcpy(), so it's not a problem. However, when dev->addr_len is greater than 22 (e.g. MAX_ADDR_LEN), arp_netmask is overwritten, which could be set as htonl(0xFFFFFFFFUL) in arp_ioctl() before calling arp_req_get(). To avoid the overflow, let's limit the max length of memcpy(). Note that commit b5f0de6df6dc ("net: dev: Convert sa_data to flexible array in struct sockaddr") just silenced syzkaller. [0]: memcpy: detected field-spanning write (size 16) of single field "r->arp_ha.sa_data" at net/ipv4/arp.c:1128 (size 14) WARNING: CPU: 0 PID: 144638 at net/ipv4/arp.c:1128 arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Modules linked in: CPU: 0 PID: 144638 Comm: syz-executor.4 Not tainted 6.1.74 #31 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.0-debian-1.16.0-5 04/01/2014 RIP: 0010:arp_req_get+0x411/0x4a0 net/ipv4/arp.c:1128 Code: fd ff ff e8 41 42 de fb b9 0e 00 00 00 4c 89 fe 48 c7 c2 20 6d ab 87 48 c7 c7 80 6d ab 87 c6 05 25 af 72 04 01 e8 5f 8d ad fb <0f> 0b e9 6c fd ff ff e8 13 42 de fb be 03 00 00 00 4c 89 e7 e8 a6 RSP: 0018:ffffc900050b7998 EFLAGS: 00010286 RAX: 0000000000000000 RBX: ffff88803a815000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff8641a44a RDI: 0000000000000001 RBP: ffffc900050b7a98 R08: 0000000000000001 R09: 0000000000000000 R10: 0000000000000000 R11: 203a7970636d656d R12: ffff888039c54000 R13: 1ffff92000a16f37 R14: ffff88803a815084 R15: 0000000000000010 FS: 00007f172bf306c0(0000) GS:ffff88805aa00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f172b3569f0 CR3: 0000000057f12005 CR4: 0000000000770ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 PKRU: 55555554 Call Trace: <TASK> arp_ioctl+0x33f/0x4b0 net/ipv4/arp.c:1261 inet_ioctl+0x314/0x3a0 net/ipv4/af_inet.c:981 sock_do_ioctl+0xdf/0x260 net/socket.c:1204 sock_ioctl+0x3ef/0x650 net/socket.c:1321 vfs_ioctl fs/ioctl.c:51 [inline] __do_sys_ioctl fs/ioctl.c:870 [inline] __se_sys_ioctl fs/ioctl.c:856 [inline] __x64_sys_ioctl+0x18e/0x220 fs/ioctl.c:856 do_syscall_x64 arch/x86/entry/common.c:51 [inline] do_syscall_64+0x37/0x90 arch/x86/entry/common.c:81 entry_SYSCALL_64_after_hwframe+0x64/0xce RIP: 0033:0x7f172b262b8d Code: 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f172bf300b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 RAX: ffffffffffffffda RBX: 00007f172b3abf80 RCX: 00007f172b262b8d RDX: 0000000020000000 RSI: 0000000000008954 RDI: 0000000000000003 RBP: 00007f172b2d3493 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 000000000000000b R14: 00007f172b3abf80 R15: 00007f172bf10000 </TASK> | ||||
| CVE-2024-26704 | 3 Debian, Linux, Redhat | 7 Debian Linux, Linux Kernel, Enterprise Linux and 4 more | 2025-05-04 | 7.8 High |
| In the Linux kernel, the following vulnerability has been resolved: ext4: fix double-free of blocks due to wrong extents moved_len In ext4_move_extents(), moved_len is only updated when all moves are successfully executed, and only discards orig_inode and donor_inode preallocations when moved_len is not zero. When the loop fails to exit after successfully moving some extents, moved_len is not updated and remains at 0, so it does not discard the preallocations. If the moved extents overlap with the preallocated extents, the overlapped extents are freed twice in ext4_mb_release_inode_pa() and ext4_process_freed_data() (as described in commit 94d7c16cbbbd ("ext4: Fix double-free of blocks with EXT4_IOC_MOVE_EXT")), and bb_free is incremented twice. Hence when trim is executed, a zero-division bug is triggered in mb_update_avg_fragment_size() because bb_free is not zero and bb_fragments is zero. Therefore, update move_len after each extent move to avoid the issue. | ||||
| CVE-2024-26698 | 3 Debian, Linux, Redhat | 7 Debian Linux, Linux Kernel, Enterprise Linux and 4 more | 2025-05-04 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: hv_netvsc: Fix race condition between netvsc_probe and netvsc_remove In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the VMBus channel"), napi_disable was getting called for all channels, including all subchannels without confirming if they are enabled or not. This caused hv_netvsc getting hung at napi_disable, when netvsc_probe() has finished running but nvdev->subchan_work has not started yet. netvsc_subchan_work() -> rndis_set_subchannel() has not created the sub-channels and because of that netvsc_sc_open() is not running. netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which netvsc_subchan_work did not run. netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the opposite. Now during netvsc_device_remove(), when napi_disable is called for those subchannels, napi_disable gets stuck on infinite msleep. This fix addresses this problem by ensuring that napi_disable() is not getting called for non-enabled NAPI struct. But netif_napi_del() is still necessary for these non-enabled NAPI struct for cleanup purpose. Call trace: [ 654.559417] task:modprobe state:D stack: 0 pid: 2321 ppid: 1091 flags:0x00004002 [ 654.568030] Call Trace: [ 654.571221] <TASK> [ 654.573790] __schedule+0x2d6/0x960 [ 654.577733] schedule+0x69/0xf0 [ 654.581214] schedule_timeout+0x87/0x140 [ 654.585463] ? __bpf_trace_tick_stop+0x20/0x20 [ 654.590291] msleep+0x2d/0x40 [ 654.593625] napi_disable+0x2b/0x80 [ 654.597437] netvsc_device_remove+0x8a/0x1f0 [hv_netvsc] [ 654.603935] rndis_filter_device_remove+0x194/0x1c0 [hv_netvsc] [ 654.611101] ? do_wait_intr+0xb0/0xb0 [ 654.615753] netvsc_remove+0x7c/0x120 [hv_netvsc] [ 654.621675] vmbus_remove+0x27/0x40 [hv_vmbus] | ||||
| CVE-2024-26686 | 2 Linux, Redhat | 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: fs/proc: do_task_stat: use sig->stats_lock to gather the threads/children stats lock_task_sighand() can trigger a hard lockup. If NR_CPUS threads call do_task_stat() at the same time and the process has NR_THREADS, it will spin with irqs disabled O(NR_CPUS * NR_THREADS) time. Change do_task_stat() to use sig->stats_lock to gather the statistics outside of ->siglock protected section, in the likely case this code will run lockless. | ||||
| CVE-2024-26673 | 3 Debian, Linux, Redhat | 5 Debian Linux, Linux Kernel, Enterprise Linux and 2 more | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_ct: sanitize layer 3 and 4 protocol number in custom expectations - Disallow families other than NFPROTO_{IPV4,IPV6,INET}. - Disallow layer 4 protocol with no ports, since destination port is a mandatory attribute for this object. | ||||
| CVE-2024-26671 | 3 Debian, Linux, Redhat | 5 Debian Linux, Linux Kernel, Enterprise Linux and 2 more | 2025-05-04 | 4.7 Medium |
| In the Linux kernel, the following vulnerability has been resolved: blk-mq: fix IO hang from sbitmap wakeup race In blk_mq_mark_tag_wait(), __add_wait_queue() may be re-ordered with the following blk_mq_get_driver_tag() in case of getting driver tag failure. Then in __sbitmap_queue_wake_up(), waitqueue_active() may not observe the added waiter in blk_mq_mark_tag_wait() and wake up nothing, meantime blk_mq_mark_tag_wait() can't get driver tag successfully. This issue can be reproduced by running the following test in loop, and fio hang can be observed in < 30min when running it on my test VM in laptop. modprobe -r scsi_debug modprobe scsi_debug delay=0 dev_size_mb=4096 max_queue=1 host_max_queue=1 submit_queues=4 dev=`ls -d /sys/bus/pseudo/drivers/scsi_debug/adapter*/host*/target*/*/block/* | head -1 | xargs basename` fio --filename=/dev/"$dev" --direct=1 --rw=randrw --bs=4k --iodepth=1 \ --runtime=100 --numjobs=40 --time_based --name=test \ --ioengine=libaio Fix the issue by adding one explicit barrier in blk_mq_mark_tag_wait(), which is just fine in case of running out of tag. | ||||
| CVE-2024-26669 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: net/sched: flower: Fix chain template offload When a qdisc is deleted from a net device the stack instructs the underlying driver to remove its flow offload callback from the associated filter block using the 'FLOW_BLOCK_UNBIND' command. The stack then continues to replay the removal of the filters in the block for this driver by iterating over the chains in the block and invoking the 'reoffload' operation of the classifier being used. In turn, the classifier in its 'reoffload' operation prepares and emits a 'FLOW_CLS_DESTROY' command for each filter. However, the stack does not do the same for chain templates and the underlying driver never receives a 'FLOW_CLS_TMPLT_DESTROY' command when a qdisc is deleted. This results in a memory leak [1] which can be reproduced using [2]. Fix by introducing a 'tmplt_reoffload' operation and have the stack invoke it with the appropriate arguments as part of the replay. Implement the operation in the sole classifier that supports chain templates (flower) by emitting the 'FLOW_CLS_TMPLT_{CREATE,DESTROY}' command based on whether a flow offload callback is being bound to a filter block or being unbound from one. As far as I can tell, the issue happens since cited commit which reordered tcf_block_offload_unbind() before tcf_block_flush_all_chains() in __tcf_block_put(). The order cannot be reversed as the filter block is expected to be freed after flushing all the chains. [1] unreferenced object 0xffff888107e28800 (size 2048): comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s) hex dump (first 32 bytes): b1 a6 7c 11 81 88 ff ff e0 5b b3 10 81 88 ff ff ..|......[...... 01 00 00 00 00 00 00 00 e0 aa b0 84 ff ff ff ff ................ backtrace: [<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320 [<ffffffff81ab374e>] __kmalloc+0x4e/0x90 [<ffffffff832aec6d>] mlxsw_sp_acl_ruleset_get+0x34d/0x7a0 [<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180 [<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280 [<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340 [<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0 [<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170 [<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0 [<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440 [<ffffffff83ac6270>] netlink_unicast+0x540/0x820 [<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0 [<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80 [<ffffffff8379d29a>] ___sys_sendmsg+0x13a/0x1e0 [<ffffffff8379d50c>] __sys_sendmsg+0x11c/0x1f0 [<ffffffff843b9ce0>] do_syscall_64+0x40/0xe0 unreferenced object 0xffff88816d2c0400 (size 1024): comm "tc", pid 1079, jiffies 4294958525 (age 3074.287s) hex dump (first 32 bytes): 40 00 00 00 00 00 00 00 57 f6 38 be 00 00 00 00 @.......W.8..... 10 04 2c 6d 81 88 ff ff 10 04 2c 6d 81 88 ff ff ..,m......,m.... backtrace: [<ffffffff81c06a68>] __kmem_cache_alloc_node+0x1e8/0x320 [<ffffffff81ab36c1>] __kmalloc_node+0x51/0x90 [<ffffffff81a8ed96>] kvmalloc_node+0xa6/0x1f0 [<ffffffff82827d03>] bucket_table_alloc.isra.0+0x83/0x460 [<ffffffff82828d2b>] rhashtable_init+0x43b/0x7c0 [<ffffffff832aed48>] mlxsw_sp_acl_ruleset_get+0x428/0x7a0 [<ffffffff832bc195>] mlxsw_sp_flower_tmplt_create+0x145/0x180 [<ffffffff832b2e1a>] mlxsw_sp_flow_block_cb+0x1ea/0x280 [<ffffffff83a10613>] tc_setup_cb_call+0x183/0x340 [<ffffffff83a9f85a>] fl_tmplt_create+0x3da/0x4c0 [<ffffffff83a22435>] tc_ctl_chain+0xa15/0x1170 [<ffffffff838a863c>] rtnetlink_rcv_msg+0x3cc/0xed0 [<ffffffff83ac87f0>] netlink_rcv_skb+0x170/0x440 [<ffffffff83ac6270>] netlink_unicast+0x540/0x820 [<ffffffff83ac6e28>] netlink_sendmsg+0x8d8/0xda0 [<ffffffff83793def>] ____sys_sendmsg+0x30f/0xa80 [2] # tc qdisc add dev swp1 clsact # tc chain add dev swp1 ingress proto ip chain 1 flower dst_ip 0.0.0.0/32 # tc qdisc del dev ---truncated--- | ||||
| CVE-2024-26668 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nft_limit: reject configurations that cause integer overflow Reject bogus configs where internal token counter wraps around. This only occurs with very very large requests, such as 17gbyte/s. Its better to reject this rather than having incorrect ratelimit. | ||||
| CVE-2024-26665 | 3 Debian, Linux, Redhat | 4 Debian Linux, Linux Kernel, Enterprise Linux and 1 more | 2025-05-04 | 7.1 High |
| In the Linux kernel, the following vulnerability has been resolved: tunnels: fix out of bounds access when building IPv6 PMTU error If the ICMPv6 error is built from a non-linear skb we get the following splat, BUG: KASAN: slab-out-of-bounds in do_csum+0x220/0x240 Read of size 4 at addr ffff88811d402c80 by task netperf/820 CPU: 0 PID: 820 Comm: netperf Not tainted 6.8.0-rc1+ #543 ... kasan_report+0xd8/0x110 do_csum+0x220/0x240 csum_partial+0xc/0x20 skb_tunnel_check_pmtu+0xeb9/0x3280 vxlan_xmit_one+0x14c2/0x4080 vxlan_xmit+0xf61/0x5c00 dev_hard_start_xmit+0xfb/0x510 __dev_queue_xmit+0x7cd/0x32a0 br_dev_queue_push_xmit+0x39d/0x6a0 Use skb_checksum instead of csum_partial who cannot deal with non-linear SKBs. | ||||
| CVE-2024-26656 | 2 Linux, Redhat | 6 Linux Kernel, Enterprise Linux, Rhel Aus and 3 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix use-after-free bug The bug can be triggered by sending a single amdgpu_gem_userptr_ioctl to the AMDGPU DRM driver on any ASICs with an invalid address and size. The bug was reported by Joonkyo Jung <joonkyoj@yonsei.ac.kr>. For example the following code: static void Syzkaller1(int fd) { struct drm_amdgpu_gem_userptr arg; int ret; arg.addr = 0xffffffffffff0000; arg.size = 0x80000000; /*2 Gb*/ arg.flags = 0x7; ret = drmIoctl(fd, 0xc1186451/*amdgpu_gem_userptr_ioctl*/, &arg); } Due to the address and size are not valid there is a failure in amdgpu_hmm_register->mmu_interval_notifier_insert->__mmu_interval_notifier_insert-> check_shl_overflow, but we even the amdgpu_hmm_register failure we still call amdgpu_hmm_unregister into amdgpu_gem_object_free which causes access to a bad address. The following stack is below when the issue is reproduced when Kazan is enabled: [ +0.000014] Hardware name: ASUS System Product Name/ROG STRIX B550-F GAMING (WI-FI), BIOS 1401 12/03/2020 [ +0.000009] RIP: 0010:mmu_interval_notifier_remove+0x327/0x340 [ +0.000017] Code: ff ff 49 89 44 24 08 48 b8 00 01 00 00 00 00 ad de 4c 89 f7 49 89 47 40 48 83 c0 22 49 89 47 48 e8 ce d1 2d 01 e9 32 ff ff ff <0f> 0b e9 16 ff ff ff 4c 89 ef e8 fa 14 b3 ff e9 36 ff ff ff e8 80 [ +0.000014] RSP: 0018:ffffc90002657988 EFLAGS: 00010246 [ +0.000013] RAX: 0000000000000000 RBX: 1ffff920004caf35 RCX: ffffffff8160565b [ +0.000011] RDX: dffffc0000000000 RSI: 0000000000000004 RDI: ffff8881a9f78260 [ +0.000010] RBP: ffffc90002657a70 R08: 0000000000000001 R09: fffff520004caf25 [ +0.000010] R10: 0000000000000003 R11: ffffffff8161d1d6 R12: ffff88810e988c00 [ +0.000010] R13: ffff888126fb5a00 R14: ffff88810e988c0c R15: ffff8881a9f78260 [ +0.000011] FS: 00007ff9ec848540(0000) GS:ffff8883cc880000(0000) knlGS:0000000000000000 [ +0.000012] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ +0.000010] CR2: 000055b3f7e14328 CR3: 00000001b5770000 CR4: 0000000000350ef0 [ +0.000010] Call Trace: [ +0.000006] <TASK> [ +0.000007] ? show_regs+0x6a/0x80 [ +0.000018] ? __warn+0xa5/0x1b0 [ +0.000019] ? mmu_interval_notifier_remove+0x327/0x340 [ +0.000018] ? report_bug+0x24a/0x290 [ +0.000022] ? handle_bug+0x46/0x90 [ +0.000015] ? exc_invalid_op+0x19/0x50 [ +0.000016] ? asm_exc_invalid_op+0x1b/0x20 [ +0.000017] ? kasan_save_stack+0x26/0x50 [ +0.000017] ? mmu_interval_notifier_remove+0x23b/0x340 [ +0.000019] ? mmu_interval_notifier_remove+0x327/0x340 [ +0.000019] ? mmu_interval_notifier_remove+0x23b/0x340 [ +0.000020] ? __pfx_mmu_interval_notifier_remove+0x10/0x10 [ +0.000017] ? kasan_save_alloc_info+0x1e/0x30 [ +0.000018] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? __kasan_kmalloc+0xb1/0xc0 [ +0.000018] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? __kasan_check_read+0x11/0x20 [ +0.000020] amdgpu_hmm_unregister+0x34/0x50 [amdgpu] [ +0.004695] amdgpu_gem_object_free+0x66/0xa0 [amdgpu] [ +0.004534] ? __pfx_amdgpu_gem_object_free+0x10/0x10 [amdgpu] [ +0.004291] ? do_syscall_64+0x5f/0xe0 [ +0.000023] ? srso_return_thunk+0x5/0x5f [ +0.000017] drm_gem_object_free+0x3b/0x50 [drm] [ +0.000489] amdgpu_gem_userptr_ioctl+0x306/0x500 [amdgpu] [ +0.004295] ? __pfx_amdgpu_gem_userptr_ioctl+0x10/0x10 [amdgpu] [ +0.004270] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? __this_cpu_preempt_check+0x13/0x20 [ +0.000015] ? srso_return_thunk+0x5/0x5f [ +0.000013] ? sysvec_apic_timer_interrupt+0x57/0xc0 [ +0.000020] ? srso_return_thunk+0x5/0x5f [ +0.000014] ? asm_sysvec_apic_timer_interrupt+0x1b/0x20 [ +0.000022] ? drm_ioctl_kernel+0x17b/0x1f0 [drm] [ +0.000496] ? __pfx_amdgpu_gem_userptr_ioctl+0x10/0x10 [amdgpu] [ +0.004272] ? drm_ioctl_kernel+0x190/0x1f0 [drm] [ +0.000492] drm_ioctl_kernel+0x140/0x1f0 [drm] [ +0.000497] ? __pfx_amdgpu_gem_userptr_ioctl+0x10/0x10 [amdgpu] [ +0.004297] ? __pfx_drm_ioctl_kernel+0x10/0x10 [d ---truncated--- | ||||
| CVE-2024-26645 | 3 Debian, Linux, Redhat | 4 Debian Linux, Linux Kernel, Enterprise Linux and 1 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tracing: Ensure visibility when inserting an element into tracing_map Running the following two commands in parallel on a multi-processor AArch64 machine can sporadically produce an unexpected warning about duplicate histogram entries: $ while true; do echo hist:key=id.syscall:val=hitcount > \ /sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/trigger cat /sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/hist sleep 0.001 done $ stress-ng --sysbadaddr $(nproc) The warning looks as follows: [ 2911.172474] ------------[ cut here ]------------ [ 2911.173111] Duplicates detected: 1 [ 2911.173574] WARNING: CPU: 2 PID: 12247 at kernel/trace/tracing_map.c:983 tracing_map_sort_entries+0x3e0/0x408 [ 2911.174702] Modules linked in: iscsi_ibft(E) iscsi_boot_sysfs(E) rfkill(E) af_packet(E) nls_iso8859_1(E) nls_cp437(E) vfat(E) fat(E) ena(E) tiny_power_button(E) qemu_fw_cfg(E) button(E) fuse(E) efi_pstore(E) ip_tables(E) x_tables(E) xfs(E) libcrc32c(E) aes_ce_blk(E) aes_ce_cipher(E) crct10dif_ce(E) polyval_ce(E) polyval_generic(E) ghash_ce(E) gf128mul(E) sm4_ce_gcm(E) sm4_ce_ccm(E) sm4_ce(E) sm4_ce_cipher(E) sm4(E) sm3_ce(E) sm3(E) sha3_ce(E) sha512_ce(E) sha512_arm64(E) sha2_ce(E) sha256_arm64(E) nvme(E) sha1_ce(E) nvme_core(E) nvme_auth(E) t10_pi(E) sg(E) scsi_mod(E) scsi_common(E) efivarfs(E) [ 2911.174738] Unloaded tainted modules: cppc_cpufreq(E):1 [ 2911.180985] CPU: 2 PID: 12247 Comm: cat Kdump: loaded Tainted: G E 6.7.0-default #2 1b58bbb22c97e4399dc09f92d309344f69c44a01 [ 2911.182398] Hardware name: Amazon EC2 c7g.8xlarge/, BIOS 1.0 11/1/2018 [ 2911.183208] pstate: 61400005 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--) [ 2911.184038] pc : tracing_map_sort_entries+0x3e0/0x408 [ 2911.184667] lr : tracing_map_sort_entries+0x3e0/0x408 [ 2911.185310] sp : ffff8000a1513900 [ 2911.185750] x29: ffff8000a1513900 x28: ffff0003f272fe80 x27: 0000000000000001 [ 2911.186600] x26: ffff0003f272fe80 x25: 0000000000000030 x24: 0000000000000008 [ 2911.187458] x23: ffff0003c5788000 x22: ffff0003c16710c8 x21: ffff80008017f180 [ 2911.188310] x20: ffff80008017f000 x19: ffff80008017f180 x18: ffffffffffffffff [ 2911.189160] x17: 0000000000000000 x16: 0000000000000000 x15: ffff8000a15134b8 [ 2911.190015] x14: 0000000000000000 x13: 205d373432323154 x12: 5b5d313131333731 [ 2911.190844] x11: 00000000fffeffff x10: 00000000fffeffff x9 : ffffd1b78274a13c [ 2911.191716] x8 : 000000000017ffe8 x7 : c0000000fffeffff x6 : 000000000057ffa8 [ 2911.192554] x5 : ffff0012f6c24ec0 x4 : 0000000000000000 x3 : ffff2e5b72b5d000 [ 2911.193404] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff0003ff254480 [ 2911.194259] Call trace: [ 2911.194626] tracing_map_sort_entries+0x3e0/0x408 [ 2911.195220] hist_show+0x124/0x800 [ 2911.195692] seq_read_iter+0x1d4/0x4e8 [ 2911.196193] seq_read+0xe8/0x138 [ 2911.196638] vfs_read+0xc8/0x300 [ 2911.197078] ksys_read+0x70/0x108 [ 2911.197534] __arm64_sys_read+0x24/0x38 [ 2911.198046] invoke_syscall+0x78/0x108 [ 2911.198553] el0_svc_common.constprop.0+0xd0/0xf8 [ 2911.199157] do_el0_svc+0x28/0x40 [ 2911.199613] el0_svc+0x40/0x178 [ 2911.200048] el0t_64_sync_handler+0x13c/0x158 [ 2911.200621] el0t_64_sync+0x1a8/0x1b0 [ 2911.201115] ---[ end trace 0000000000000000 ]--- The problem appears to be caused by CPU reordering of writes issued from __tracing_map_insert(). The check for the presence of an element with a given key in this function is: val = READ_ONCE(entry->val); if (val && keys_match(key, val->key, map->key_size)) ... The write of a new entry is: elt = get_free_elt(map); memcpy(elt->key, key, map->key_size); entry->val = elt; The "memcpy(elt->key, key, map->key_size);" and "entry->val = elt;" stores may become visible in the reversed order on another CPU. This second CPU might then incorrectly determine that a new key doesn't match an already present val->key and subse ---truncated--- | ||||
| CVE-2024-26642 | 3 Debian, Linux, Redhat | 7 Debian Linux, Linux Kernel, Enterprise Linux and 4 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_tables: disallow anonymous set with timeout flag Anonymous sets are never used with timeout from userspace, reject this. Exception to this rule is NFT_SET_EVAL to ensure legacy meters still work. | ||||
| CVE-2024-26640 | 3 Debian, Linux, Redhat | 7 Debian Linux, Linux Kernel, Enterprise Linux and 4 more | 2025-05-04 | 5.5 Medium |
| In the Linux kernel, the following vulnerability has been resolved: tcp: add sanity checks to rx zerocopy TCP rx zerocopy intent is to map pages initially allocated from NIC drivers, not pages owned by a fs. This patch adds to can_map_frag() these additional checks: - Page must not be a compound one. - page->mapping must be NULL. This fixes the panic reported by ZhangPeng. syzbot was able to loopback packets built with sendfile(), mapping pages owned by an ext4 file to TCP rx zerocopy. r3 = socket$inet_tcp(0x2, 0x1, 0x0) mmap(&(0x7f0000ff9000/0x4000)=nil, 0x4000, 0x0, 0x12, r3, 0x0) r4 = socket$inet_tcp(0x2, 0x1, 0x0) bind$inet(r4, &(0x7f0000000000)={0x2, 0x4e24, @multicast1}, 0x10) connect$inet(r4, &(0x7f00000006c0)={0x2, 0x4e24, @empty}, 0x10) r5 = openat$dir(0xffffffffffffff9c, &(0x7f00000000c0)='./file0\x00', 0x181e42, 0x0) fallocate(r5, 0x0, 0x0, 0x85b8) sendfile(r4, r5, 0x0, 0x8ba0) getsockopt$inet_tcp_TCP_ZEROCOPY_RECEIVE(r4, 0x6, 0x23, &(0x7f00000001c0)={&(0x7f0000ffb000/0x3000)=nil, 0x3000, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0}, &(0x7f0000000440)=0x40) r6 = openat$dir(0xffffffffffffff9c, &(0x7f00000000c0)='./file0\x00', 0x181e42, 0x0) | ||||
| CVE-2024-26638 | 2 Linux, Redhat | 3 Linux Kernel, Enterprise Linux, Rhel Eus | 2025-05-04 | 4.4 Medium |
| In the Linux kernel, the following vulnerability has been resolved: nbd: always initialize struct msghdr completely syzbot complains that msg->msg_get_inq value can be uninitialized [1] struct msghdr got many new fields recently, we should always make sure their values is zero by default. [1] BUG: KMSAN: uninit-value in tcp_recvmsg+0x686/0xac0 net/ipv4/tcp.c:2571 tcp_recvmsg+0x686/0xac0 net/ipv4/tcp.c:2571 inet_recvmsg+0x131/0x580 net/ipv4/af_inet.c:879 sock_recvmsg_nosec net/socket.c:1044 [inline] sock_recvmsg+0x12b/0x1e0 net/socket.c:1066 __sock_xmit+0x236/0x5c0 drivers/block/nbd.c:538 nbd_read_reply drivers/block/nbd.c:732 [inline] recv_work+0x262/0x3100 drivers/block/nbd.c:863 process_one_work kernel/workqueue.c:2627 [inline] process_scheduled_works+0x104e/0x1e70 kernel/workqueue.c:2700 worker_thread+0xf45/0x1490 kernel/workqueue.c:2781 kthread+0x3ed/0x540 kernel/kthread.c:388 ret_from_fork+0x66/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x11/0x20 arch/x86/entry/entry_64.S:242 Local variable msg created at: __sock_xmit+0x4c/0x5c0 drivers/block/nbd.c:513 nbd_read_reply drivers/block/nbd.c:732 [inline] recv_work+0x262/0x3100 drivers/block/nbd.c:863 CPU: 1 PID: 7465 Comm: kworker/u5:1 Not tainted 6.7.0-rc7-syzkaller-00041-gf016f7547aee #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/17/2023 Workqueue: nbd5-recv recv_work | ||||